remote power controllers up to 200 amps ? form x mag netic latching for ac only applications contact arrangement ........................... spst (1 form x) weight ............................................................... 15 oz max. designed to meet the requirements of mil - c - 83383 con tact ratings (note 1): power contacts: all loads ...................... up to 200 amps @ 115 vac current trip points .................................... trip time 1000% of rated current .................... 1.0 sec. max. 400% of rated current ..................... 10.0 sec. max. 200% of rated current ..................... 60.0 sec. max. 138% of rated current ...................... 1.0 hour max. up to 115% of rated current ....................... no trip tolerances: current ............................................................. 10% time ................................................................. 10% auxiliary contacts: configuration ................................................... spdt current rating ........................... 5 amps @ 28 vdc life ............... 50,000 cycles @ rated res. and ind. load 25,000 cycles @ rated motor load 100,000 cycles mechanical rupture (main contacts) .......................... 3600 amperes response time: ............................................. 12 ms nom. contact bounce time ....................................... 2 ms max @ rated contact load, 115 vac contact voltage drop : initial ...................................... 225 mv @ rated current end of life ............................. 250 mv @ rated current operating voltage: nominal ac voltage ............................ 10 4 to 122 vac temperature range ................................. - 54 o c to +71 o c vibration (note 2) .............................. 10 g's 50 - 2000 hz shock (operating) (note 2) ......................... 25 g's 11 ms acceleration ............................................................... 15 g duty cycle ........................................................ intermittent insulation resistance ............................... 100 megohms @ 500v 25 o c dielectric strength: sea level: contact to case ................................... 1,500 vrms contact to coil ..................................... 1,500 vrms coil to case ......................................... 1,500 vrms across open contacts ........................ 1,350 vrms 50,000 feet: all points ................................................. 500 vrms n otes : 1 . for other ratings or calibrations consult the factory. 2 . for applications requiring higher shock and vibration, c onsult the factory. 700 series 1 www.microsemi.com ? 2015 microsemi corporation june 2015 rev. 5 general s pecifications performance environmental electrical characteristics downloaded from: http:///
the 700 remote power controllers are designed to sense the current level flowing through their contacts, and to open the circuit when the current exceeds the specified current rating. these units use our unique magnetic latching motor design to minimize power consumption. these units are fully temperature compensated for accurate operation over the full temperature range. the 700 circuitry has 1500 watts of peak power dissipation transient suppression built in so it can withstand the rigors of even the noisiest of supply v oltages. utilizing all space age approved materials, the 700 remote power controllers are ideal for demanding applicat ions. r.p.c. type nominal current rating "a" indicates spdt auxiliary switch 700 - 150 a catalog number continuous ampere contact rating thre ad "b" dimension "a" 700 - 5( ) 5 10 - 32 unf .500 700 - 7.5( ) 7.5 10 - 32 unf .500 700 - 10( ) 10 10 - 32 unf .500 700 - 15( ) 15 10 - 32 unf .500 700 - 20( ) 20 10 - 32 unf .500 700 - 25( ) 25 10 - 32 unf .500 700 - 35( ) 35 1/4 - 28 unf .610 700 - 40( ) 40 1/4 - 28 unf .610 700 - 50( ) 50 1/4 - 28 unf .610 700 - 60( ) 60 1/4 - 28 unf .610 700 - 75( ) 75 1/4 - 28 unf .610 700 - 100( ) 100 1/4 - 28 unf .610 700 - 125( ) 125 1/4 - 28 unf .610 700 - 150( ) 150 1/4 - 28 unf .610 700 - 175( ) 175 1/4 - 28 unf .610 700 - 200( ) 200 1/4 - 28 unf .610 ? unless otherwise specified, all tests made at nominal coil voltages, @ 25 o c. ? for special coil variations, switching configurations,terminals styles and mounting types, consult the factory. ? unless otherwise specified, tolerances on decimal dimensions are .010". ? specifications contained herein are subject to change without notice. overall dimensions selection table schematic typical wiring diagram trip time curve general notes 2 downloaded from: http:///
700 - 5 /06.15 microsemi corporate headquarters one enterprise, aliso viejo, ca 92656 usa within the usa : +1 (800) 713-4113 outside the usa : +1 (949) 380-6100 sales : +1 (949) 380-6136 fax : +1 (949) 215-4996 e-mail: sales.support@microsemi.com microsemi corporation (mscc) offers a compreh ensive portfolio of semiconductor and system solutions for communicati ons, defense & security, aerospace and industrial markets. products include high-performance and radiation-hardene d analog mixed-signal integrated circuits, fpgas, socs and asics; power management pr oducts; timing and synchronization devices and precise time solutions, setting the world's standard for time; voice processing devices; rf solutions; discrete components; security technologies and scalable anti-tamper products; ethernet solutions; power-over-ethernet ics and midspans; as well as custom design capabilities and services. microsemi is head quartered in aliso viejo, calif., and has approximately 3,600 employees globally. learn more at www.microsemi.com . ? 2015 microsemi corporation. all rights reserved. microsemi and the microsemi logo are trademarks of microsemi corporation. all other trademarks and service marks are the property of their respective owners. microsemi makes no warranty, representation, or guarantee regarding the information contained herein or the suitability of its products and services for any particular purpose, nor does microsemi assume any liability whatsoever arising out of the application or use of any product or circuit. the products sold hereunder and any other products sold by microsem i have been subject to li mited testing and should not be used in conjunction with missi on-critical equipment or applications. any performance specifications are believed to be reliable but are not verified, and buyer must conduct and complete all performance and other testing of the products, alone and together with, or installed in, any end-products. buyer shall not rely on any data and performance specifications or para meters provided by micr osemi. it is the buyer's responsibility to independently determine suitability of any products and to test and verify the same. the information provided by microsemi hereunder is provi ded "as is, where is" and with all faults, and the entire risk associated with such information is entirely with the buyer. microsemi does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other ip rights, whether with regard to such information itself or anything described by such in formation. information provided in this document is proprietary to microsemi, and microsemi reserves the ri ght to make any changes to the information in this document or to any products and services at any time without notice. downloaded from: http:///
|
